This servo saver allows you to absorb the impacts on the wheels of your RTA and to avoid premature wear of your servo. This option also makes the entire steering system more reliable, stronger and more precise.
Set of 5* M2 countersunk head screws, length 6mm for the RTA V1.2. Torx T6 head.
Set of 2* M2 round head screws, length 5mm for the RTA V1.2. Torx T6 head.
This set of 4 anodized aluminum setup wheels allows you to fine-tune your 2WD Mini-Z (GLA, BZ, BZ3, SZ, FFZ…) Machined with very low tolerances, these setup wheels will allow you to measure and adjust the following parameters: The weight on each wheel of your Mini-z (cross weight) The camber of your wheels […]
Brass inserts to ballast the aluminum (RT080) and brass (RT084) option chassis of the RTA. Each insert weighs 2.6gr and is screwed using 2 micro screws. This option helps to cover a wider range of mass distribution on the chassis as well as to lower the center of gravity as much as possible. […]
Custom made spring kit to adjust the different characteristics of the RTA V1.2 chassis. For body and chassis of model car 1/28 radio controlled.
This part is machined from high quality plastic.
This part is machining in good quality anodized aluminium 7075-T6
This part is machining in good quality anodized aluminium 7075-T6
This set allows to use the rear suspension of the RTA V1.2 This set is adaptable on RTA V1 and RTA V1.2 This new rear suspension increases the grip and the stability of the rear axle. It provides a very free and easy to adjust rear axle. The addition of a rear […]
High quality resin 3D printing case allowing the storage of nano receivers and robi transponders while isolating the two components from each other. Fits on RTA, GLR, MRZ, GLA, BZ3 and most Mini-z chassis.
Optional brass chassis for RTA. Possibility to add brass inserts (RT090) to adjust the weight distribution. The chassis weighs 40gr and each brass weight weighs 2.6gr. So you can reach a total weight of 50.4gr. The original chassis weighs 19gr. So, this option helps to add a maximum of weight to the […]
Replacing these clamps with the original one allows to add 1.8gr on each side of the RTA whether at the front or at the rear: Brass clamps on the rear plate => Used to stabilize and increase the rear grip of your RTA. Brass flanges on chassis => Allows to have better corner entry […]
This kit allows you to adjust the roll of the RTA. With 3 different bar hardnesses, you will be able to allow more or less roll to the chassis. Once installed, the anti-roll system is easy to enable/disable with a single screw. The following parts are required to use this option: […]
Optional aluminum chassis for RTA. Possibility to add brass inserts (RT090) to adjust the weight distribution. The chassis weighs 16gr and each brass weight weighs 2.6gr. So you can reach a total weight of 26.4gr. The original chassis weighs 19gr. So, this option helps you to have a wider range of mass […]
Dual spring shock absorber allowing to adjust the compression and the rear droop of your mini-z. Highly recommended to improve the performance of your RTA. For 1 / 28th radio-controlled model chassis.
Aluminum front mount base allowing to adapt all RTRC carbon bumper on RTA or MRZ. This support allows different combinations: Fixing of a PN racing carbon body support. Fixing of an RTRC bumper to use lexan body post. Fixing of a PN carbon body support + RTRC carbon bumper This support fits on […]
This kit allows you to modify the wheelbase of your RTA from 98mm to 102mm. This will allow you to use LM type bodies as well as increase the stability of your RTA. The kit is delivered with medium hardness side carbon plates, other hardnesses are available individually.
This friction plate allows you to use lexan body post to fix lexan bodies but also hard bodies on the RTA. Holes for body posts are spaced as far as possible in order to increase the stability of the body on the chassis. This option is only available in the 98mm version.